Asked by: Asura Sulzer
style and fashion mens sportswear

Does Home Depot do crown molding?

33
Crown - Moulding - Moulding & Millwork - The Home Depot.


Accordingly, does Home Depot cut crown molding for you?

No. Cutting crown molding requires a compound cut where you both change the angle vertically and horizontally.

does Home Depot sell foam crown molding? Polystyrene - Crown - Moulding - Moulding & Millwork - The Home Depot.

what is the going rate for installing crown molding?

The average cost to install crown molding is $7 to $16 per linear foot depending on the materials chosen and labor costs. For an average living room, crown molding costs $464 to $1,102, while a kitchen costs between $210 to $570, and an entire home costs between $2,000 and $4,000 for both labor and installation.

Is crown molding out of style?

If they have crown molding in their house=Crown molding never goes out of style. The only reason you no longer see it is because people can't afford it. If they don't have crown molding=Crown molding is out of style.

Related Question Answers

Aguasantas Stumpner

Professional

What degree do you cut crown molding?

Using a power miter saw is the best way to cut crown moulding angles. The saw can be adjusted to cut at any angle–set it to 45 degrees for one side of a standard 90-degree corner. The saw can be set to 45 degrees to the left or 45 degrees to the right.

Abdelhakim Ferraris

Professional

What is the difference between 52 38 and 45 45 crown molding?

To find out what the spring angle is, set the crown molding into the crotch of a framing square and check where the ends align. if both numbers are the same, it is 45/45 crown. If the numbers are different, such as three inches on the wall and two inches on the ceiling, it is 52/38 crown.

Agapita Hasnaoui

Explainer

How do you cut and install crown molding?

To install crown molding:
  1. Measure the length of each wall.
  2. Set the miter saw to a 45° angle.
  3. Position the bottom of the molding against the saw fence and table.
  4. Tilt the molding so the back is flush with the saw fence.
  5. Cut the crown molding to length.
  6. Hold the molding on the wall, and nail it in place to the studs.

Mireira Bouza

Pundit

Does crown molding add value to home?

Installing it correctly – Despite what others may tell you, crown molding is quite difficult to install. Painting it professionally – Last, but not least, crown molding can increase your home's value only when it's painted professionally. In case of a bad paint job, it does nothing for your home – or worse.

Arevik Musahanyants

Pundit

Which rooms should have crown molding?

As we mentioned, crown molding is often installed between walls and the ceiling or the wall and the floor. This gives the room a seamless, elegant appearance.

Here are a few:
  • Kitchen Cabinets.
  • Bathroom Mirrors.
  • Bedroom Headboard.
  • Shelving.
  • Around Your Mounted TV.

Junxiang Potts

Pundit

What size crown molding should I use for 8 foot ceilings?

For an 8 foot ceiling height the recommended crown size is 2-1/2″ to 6″ tall with no picture mold.

Nouha Schaupeter

Teacher

Do you paint Crown Moulding before installing?

Painting New Walls
If your walls are new and have never been painted, you must paint them prior to installing crown molding. Use a primer suitable as the first coat on drywall, wait for it to dry, then apply a coat of the color that you would like for your room.

Blanka Azar

Teacher

Does crown molding make room look smaller?

Crown molding does not make a room look smaller -- in most instances. The molding can be wider if the ceiling is a little higher and can be up to 6 inches wide for a very high ceiling -- up to 12 feet. Crown molding any wider than this is only suitable for very large rooms or very tall ceilings, or both.

Janira Cego

Teacher

How much crown molding do I need?

Divide the total number of inches by 12 to convert from inches to linear feet. For example, if your wall measured 40 inches in length, and you are installing molding on the top and bottom, 40 x 2 = 80 inches. Divide 80 by 12 to get 6.66 linear feet.

Fredrik Algobia

Teacher

How hard is it to install crown molding?

The hardest part of installing crown molding is cutting the corners. You can't do it like any other trim pieces because the molding sits at an angle between the wall and the ceiling (Image 1). Using a coping saw (Image 2) is the easiest way to cut the corners because a coped joint is tighter than a mitered joint.

Lucinio Lavayen

Reviewer

Does crown molding have to be the same in every room?

You don't have to put crown molding in every room to get a good effect. Putting crown molding in main rooms like living rooms, family rooms, dining rooms and kitchens will produce an elegant effect. It's less important in bedrooms and bathrooms, although it can certainly be used successfully in those areas.

Ilies Ruzicka

Reviewer

What is the going rate for baseboard installation?

Some might charge per hour (ranging from $50 to $100 an hour); some might charge per foot ($1.50 to $2 a foot). Either way, baseboard installation is the type of project a contractor should see in person before determining an accurate estimate. It's a tough job to ballpark over the phone.

Hiltrud Etzold

Reviewer

What is polyurethane crown Moulding?

Polyurethane Moulding
Polyurethane is a dense foam material that has all of the advantages of wood without the disadvantages (rotting, splintering, and cracking). Let's take a look at why polyurethane is a superior material to install.

Ridwan Gibbons

Reviewer

What is MDF crown molding?

Medium-Density Fiberboard (MDF) crown molding can be used in rooms where trim is painted. MDF is a stable and low-cost alternative to solid wood. It comes in a wide range of stock profiles, some with a natural wood veneer suitable for staining.

Ibana Abulkhanoff

Supporter

What is stain grade trim?

Stain grade is any type of milled wood suitable for staining. It can be hard or softwood, and has been planed and sanded in preparation for finishing. If the process is stopped at a certain stage, the wood is sold as rough, or paint, grade.

Ivy Bauduin

Beginner

How do you install polystyrene Moulding?

How to Install Foam Molding
  1. Measure for foam moldings as you would for traditional wood molding.
  2. Cut foam moldings with a power or hand miter saw.
  3. Purchase a water-based adhesive caulk.
  4. Run a pencil-sized zigzag of adhesive down the back of the molding.
  5. Use painter's caulk to fill gaps in joints.

Mfedla Tobolin

Beginner

How much does foam crown molding cost?

Cost of Crown Molding Per Linear Foot
Material Cost Per Linear Foot
Polyurethane $2 – $6
Vinyl or PVC $1 – $3
Foam or Polystyrene $1 – $2
Metal $20 – $25

Ange Likunov

Beginner

Can polystyrene Moulding be used outside?

Foamed Polystyrene Exterior Trim
For a long time polystyrene trim has been used on the interior of the home. With recent advancements in the way that it can withstand UV rays, polystyrene foam can now be taken outside.

Sadou Havez

Beginner

What is finger jointed trim?

Finger-jointed
When carpenters plan to stain interior trim, their first choice is solid wood. Its made by gluing small pieces of clear stock together with the help of multiple finger joints – hence it's name.

Co-Authored By:

EveryThingWhat Staff Editor

4

17th January, 2020

61

80% of readers found this page helpful.

4.1/5

Click a star to add your vote

Similar Asks
Trending