Asked by: Nelutu Marggraff
home and garden home appliances

How do I change the agitator on my Kenmore washer?

11
In that case, you'll have to remove the agitator on your Kenmore washer in order to make way for a new one.
  1. Turn off your washer and unplug it from the wall. Lift up the hood to reveal the washer tub and agitator.
  2. Remove the agitator cap.
  3. Remove the agitator bolt.
  4. Put on the safety gloves.


Correspondingly, what causes a washer not to agitate or spin?

If your washer fills with water but doesn't agitate, the problem is likely to be a faulty lid switch, a broken belt, or a problem with the motor. (Note: Direct-drive washing machines do not have belts.) 1 Check the washing machine's spin cycle. If this works, the motor is operating and the belt is not broken.

Additionally, are washers without agitators good? Despite the potential risk in damaging clothes, top load washers with agitators provide a better cleaning performance. Whereas, top load washers with no agitator may be more gentle to clothes, they really arent as effective at cleaning clothes compared to top load washers with an agitator.

Also asked, why won't my Kenmore washer agitate?

If the washer won't agitate the drive block or bell might be worn out or broken. The drive block connects the washer transmission to the agitator, if it's worn out the transmission shaft will still move back and forth but the agitator will either stay still or move slightly.

Is the agitator supposed to spin?

The agitator is a small piece that sits in the center of your washing machine. When the unit is turned on, it will spin in a clockwise motion to help circulate water throughout. Unfortunately, however, it's all too common for the agitator to break or stop working properly.

Related Question Answers

Xavi Timin

Explainer

How do I troubleshoot my Kenmore washer?

  1. Washer will not stop when the lid is open. Bad lid switch.
  2. Water will not drain out of the washer. Clogged waste hose. Bad drain pump. Bad pump motor.
  3. Washer does not spin/agitate. Broken drive belt. Bad tub motor.

Tarsicio Chaganov

Explainer

What does the agitator do in a washing machine?

Agitators. An agitator is a spindle that sticks up in the center of an automatic washing machine's wash drum. The agitator is usually equipped with fins or vanes, and it twists and turns during the machine's wash cycle, moving clothes through the water and, ideally, removing dirt from them.

Davinder Funez

Pundit

Can you take an agitator out of a washing machine?

Unplug your washing machine from the wall before you get started removing the agitator. Lift the lid on your washer to expose the agitator. Pull the fabric soften dispenser from the top of the agitator. Twist the screwdriver to pop the cap from the top of the agitator.

Cherifa Lutomsk

Pundit

How much is a washing machine agitator?

Top-load agitators have long been about function instead of form. But manufacturers now offer some models that are more stylish and have larger capacities as well, pushing up prices to between $650 and $1,300. At the same time, prices on other types of washers have come down.

Boutaina Kunnemann

Pundit

How do you get a stuck agitator out of a washing machine?

ANSWER: To remove a tightly-fitted agitator or one that has become firmly glued in place by soap residue, first unplug the washer and remove the agitator cap. Then, if there is room between the bottom edge of the agitator and the tub bottom, work a completely deflated bicycle tire in underneath the agitator.

Ulla Rook

Teacher

Why do clothes get stuck under agitator?

Why are clothes getting stuck under the agitator? When the washplate tilts it can tilt too far and allow clothes to get between the rubber seal around the washplate and the basket and it will pull the clothing down and under.

Elsie Revenga

Teacher

How do I know if my dog agitator is bad?

The best way to tell if the agitator dogs are bad is to try to turn the top of the agitator. If the agitator will turn freely both ways, the dogs are bad and need replacing. If it only turns one way, the dogs are working properly and your problem is elsewhere.

Corrinne Grunendahl

Supporter

How long do washing machines last?

The average life expectancy of a new washing machine is 11 years. Consumer Reports recommends replacing any appliance that's more than eight years old, unless it's a high-end model and has a particular appeal to you. Others suggest replacing any top-loading washer manufactured in 1999 or earlier.

Zhihong Webb

Supporter

How do I fix the agitator on my Kenmore washer?

In that case, you'll have to remove the agitator on your Kenmore washer in order to make way for a new one.
  1. Turn off your washer and unplug it from the wall. Lift up the hood to reveal the washer tub and agitator.
  2. Remove the agitator cap.
  3. Remove the agitator bolt.
  4. Put on the safety gloves.

Roya Aciondo

Supporter

Why is my washer agitator slow?

If the washer is overloaded the top part of the agitator may turn slowly. If the transmission shaft is aggressively agitating then the problem will most likely be with the agitator. If the transmission shaft is sluggish then the problem is most likely with the transmission itself.

Natosha Sackarndt

Beginner

How do I know if my agitator is working?

The agitator should start to oscillate back and forth, mixing up the clothes in the water. If the agitator does not move, double check that the sensor is depressed. If it still does not move with the sensor depressed, the agitator is broken and should be repaired.

Devona Falzone

Beginner

What is the best washer with an agitator?

These are the best top-load agitator washers we tested ranked, in order:
  • Maytag MVWB865GC.
  • GE GTW685BSLWS.
  • Maytag MVWB765FW.
  • Maytag MVWC465HW.
  • Maytag MVWC565FW.

Xiaolin Estaqueiro

Beginner

Why is my Kenmore washer not spinning?

If the washer won't spin or agitate, check the drive belt. If the belt is broken or if it isn't tight on the pulleys the washer won't spin or agitate properly. If the washer won't spin the lid switch assembly might be defective. If the washer won't spin or agitate the drive motor might be defective.

Dionne Pocock

Beginner

Why won't my Kenmore washer drain?

If the washer won't drain there might be a clogged pump or hose. It's common for small socks or other small clothing items to get into the water drain system and clog the hose leading to the pump or the pump itself. If the washer won't drain the lid switch assembly might be defective. This is a very common problem.

Hina Aganov

Beginner

How do you reset a Kenmore washing machine?

How to Reset a Kenmore Elite HE Washer
  1. Press the "Stop" button twice, and then press the "Power" button.
  2. Choose a wash cycle (e.g. "Normal"), and then choose your wash options (e.g. "Hot/Cold" or "Cold/Cold").
  3. Press the "Start" button to complete the reset process and restart the washing machine.

Manoli Schaefer

Beginner

How do I clean the filter on my Kenmore top load washer?

How to Clean the Lint Trap in a Kenmore Washing Machine
  1. Lift up the lid to your Kenmore washing machine.
  2. Twist off the top of the agitator, the bar in the center of the machine that moves the laundry around.
  3. Pull out the plastic lint trap. Empty any debris in the trap and throw the debris away.
  4. Screw the agitator's top back on. Hollan Johnson.

Maricarmen Camerer

Beginner

How do I find out what year my Kenmore washer is?

It begins with two letters, followed by several numbers. The first number represents the year of manufacture. In more current models, the number "2" represents the year 2002, "3" represents 2003, "4" represents 2004, and so on. The next two numbers identify the week of the year that the washer was built.

Co-Authored By:

EveryThingWhat Staff Editor

9

4th February, 2020

30

89% of readers found this page helpful.

4/5

Click a star to add your vote

Similar Asks
Trending