Asked by: Cheryle Vakil
business and finance aviation industry

How do you calculate spring load?

42
Load and Travel Formulas
To calculate the distance traveled of your spring you must divide the load by the spring rate. On the other hand, to calculate the working loads, you must multiply the distance traveled by the spring rate.


Similarly, it is asked, what is the load of a spring?

Spring Load. You have a spring with a free length of 5 inches and your spring rate is of 7.5 pounds of force per inch (lbf/in). This spring needs to reach a solid height of 3 inches, therefore having to travel 2 inches.

Beside above, how do you determine spring rate? To test the spring rate, the spring is placed into a spring rate tester, like shown above, and is pre-compressed one inch (or millimeters if you're using that measurement) and then compressed further to get the measurement for the next inch of compression.

Also Know, how is load rate calculated?

Calculate the hydraulic loading rate with the formula: Hydraulic loading rate = Design flow (gal/day) / Area (feet ^2). Design flow is the volume of waste water per day. Calculate the organic loading with the formula: Organic matter = (BOD5 (mg/l) * 3.785 l/gal) / 453,600 mg/lb.

What is the formula for calculating spring load?

To calculate the distance traveled of your spring you must divide the load by the spring rate. On the other hand, to calculate the working loads, you must multiply the distance traveled by the spring rate.

Related Question Answers

Diosnel Zarauz

Professional

What is a good spring rate?

The weight balance between the front and rear of a vehicle can range widely from 50%/50% (Front/Rear) to 60%/40% (Front/Rear). If you're guessing blindly, use a 55%/45% weight balance; however, it is much more appropriate to measure your car.

Naheed Ferradas

Professional

What is K in Hooke's Law?

Mathematically, Hooke's Law can be written as F=-kx. Many materials obey this law as long as the load does not exceed the material's elastic limit. The rate or spring constant, k, relates the force to the extension in SI units: N/m or kg/s2.

Marlies Meluria

Professional

What is spring constant k?

k is the spring constant, in Newtons per meter (N/m), and x is the displacement of the spring from its equilibrium position. The spring constant, k, is representative of how stiff the spring is. Stiffer (more difficult to stretch) springs have higher spring constants.

Coumba Laxmanan

Explainer

How much weight can a spring hold?

How much weight can a spring support? The maximum load that a standard variable spring can support is 50,000 lbs. The maximum load that a standard constant spring can support is 90,000 lbs.

Collene Gerckens

Explainer

What is the ideal spring?

Ideal Spring – a notional spring used in physics—it has no weight, mass, or damping losses. The force exerted by the spring is proportional to the distance the spring is stretched or compressed from its relaxed position.

Mohamad Izabel

Pundit

How do you find the tension force of a spring?

For example, where R=10 pounds per inch, P=20 pounds and T=1.5 inches, you can find the pounds of force for your spring's initial tension.

Initial Tension Formula: How to Measure Spring Tension
  1. P1 = Initial Tension.
  2. P = Load.
  3. R = Rate.
  4. T = Travel.

Turia Islanov

Pundit

What is a good load factor?

Its value is always less than one because maximum demand is never lower than average demand, since facilities likely never operate at full capacity for the duration of an entire 24-hour day. A high load factor means power usage is relatively constant. Low load factor shows that occasionally a high demand is set.

Goran Wohlmuth

Pundit

What is average load factor?

Definition: Load factor is defined as the ratio of the average load over a given period to the maximum demand (peak load) occurring in that period. In other words, the load factor is the ratio of energy consumed in a given period of the times of hours to the peak load which has occurred during that particular period.

Yunyun Grage

Pundit

What is the loading rate?

Loading rate is the speed at which you apply forces to the body. The steeper slope (top graph) means that the forces applied to the runner occur quicker than that of the forces applied to the less steep slope (bottom).

Raimondas Ruchir

Pundit

How do you calculate total demand load?

Using Load Factor to Determine Demand Limit
  1. 3000 kWh divided by 720 hours = 4.16 (demand limit if at 100% load factor)
  2. 4.16 divided by .60 = ~7kW.
  3. 20kW multiplied by 720 hours = 14,400 Total kWh (if at 100% load factor) 3000 kWh divided by 14,400 Total kWh = 21% load factor at 20kW.

Parthenia Margalef

Teacher

How do you check a coil spring?

Here are a few symptoms that will let you know if your coil springs have worn out.
  1. Sharp Vehicle Sagging.
  2. Unusual Tire Wear.
  3. Unsettling Noise.
  4. Harsh Vehicle Bounce.
  5. Abrupt Vehicle Sway.

Elli Quejido

Teacher

What is coilover spring rate?

Spring rate is expressed as the amount of force required to compress a spring a set distance. The measurement is expressed in metric (kg/mm) or in standard (lbs/in). What does it mean when they say 8K or 500lb Spring Rate? If you apply 500 lbs of weight to the top of the spring it will compress 1 inch.

Co-Authored By:

EveryThingWhat Staff Editor

8

9th May, 2020

35

92% of readers found this page helpful.

4.6/5

Click a star to add your vote

Similar Asks
Trending