Asked by: Koldobika Eeckhoff
technology and computing computer peripherals

How do you calibrate a smart level?

18
Place the SmartTool on a flat vertical surface so the so the LCD is at the bottom and away from the vertical surface. After display stops changing (wait 10 seconds to be safe), carefully press and hold the “Calibrate” button until “Cal 1” shows on the display. (See picture inset) Angle reading will appear and flash.


Similarly, you may ask, how do you calibrate a Johnson level?

Press and hold the CAL/REF key for 3-plus seconds, unit will beep once. When the LCD shows -0-, the digital level has entered the calibration mode. 2. Place the digital level on the horizontal reference surface, as shown in figure 5, after 10 seconds, press the CAL/REF again, and the LCD shows -1-.

Secondly, what is a smart level? Smart Level permits you to find level and plumb in two ways. For quick references, use the sensitive bubble vials. For highly precise work, use the digital display on the Sensor Module. It provides accuracy to 1/10 of a degree.

Considering this, how do you calibrate a Smartboard?

Calibrating your interactive flat panel with Windows 7, Windows 8 and Windows 10 operating systems

  1. Open Control Panel > Tablet and PC Settings.
  2. Click Calibrate.
  3. Press each target with an interactive flat panel pen as it appears.
  4. Follow the instructions on the interactive flat panel.

What is a smart tool?

SmartTool permits you to find level and plumb in two ways. So when you are not dealing with level or plumb, SmartTool quickly tells what the angle is and what the angle needs to be. And only SmartTool allows you to measure angles three different ways: degrees, percent slope, and pitch (rise over run).

Related Question Answers

Saray Giannini

Professional

How do you calibrate a laser level?

How to Calibrate a Rotary Laser Level
  1. Step 1 – Set-Up All Equipment. Place the tripod at least 100 feet from the wall or pole.
  2. Step 2 – Manipulate the Laser. Turn the laser towards the target (wall or pole).
  3. Step 3 – Turn on the Device. Turn on the laser.
  4. Step 4 – Repeat at 180°
  5. Step 5 – Rotate at 90º
  6. Step 6 – Manipulate the Adjuster Knob.

Fleta Rathore

Explainer

How do I calibrate my Sitepro dl48?

Press the CALIBRATE button and hold down for 4 seconds. The LCD screen will display CAL1. Put the digital level on a fiat surface and press the CALIBRATE button again, the number 1 will start to fiash. After a few seconds, the display will change to CAL2.

Hiart Sanchez Miranda

Explainer

How do you use digital level?

How to Use a Digital Electronic Level
  1. Place the digital electronic level on the surface you want to measure.
  2. Wait a moment for the level to settle on a degree reading.
  3. Adjust the surface accordingly to bring the degree reading to 0.0 degrees, or level.

Mariona Camporro

Pundit

How do you calibrate a Topcon laser?

The Topcon RL-H3C is now in calibration mode, to select the “X” axis press the “TILT” button (left button) and the “ON” light will go solid. Next press “TILT” once more and the axis is locked in and ready to adjust. Press the “MANU” or “Power” buttons to shift the beam up or down to align with your level mark.

Ashlee Enci

Pundit

How do I calibrate my e70 Smartboard?

To calibrate your SMART Board E70
  1. Launch 'orient' from the system tray or SMART settings.
  2. When you launch orient, a screen appears asking you to touch a cross.
  3. If you have multiple displays, follow the on-screen instructions to move the cross until its visible on your SMART Board E70 touch interface.
  4. Tap the cross.

Xiaofang Veltens

Pundit

Where is the reset button on Smartboard?

The Reset button is located behind the lower-right side of the interactive whiteboard (when viewed from the front). 2. To reset all components of the SMART Board interactive whiteboard, disconnect and then reconnect the USB cable.

Elizabhet Astalarra

Teacher

How do you calibrate a board?

Calibrating the Promethean Board can also be done using the computer software.
  1. Select the triangle on the bottom right of the taskbar of a PC.
  2. Select the Promethean icon – PC (You will find this icon in the menu bar at the top of the screen on a Mac)
  3. Select calibration from the menu. Then select 5 points.

Momar Unzaga

Teacher

How do I calibrate my m600 Smartboard?

To calibrate your interactive whiteboard
The first time you connect the interactive whiteboard, press the Please calibrate the SMART Board interactive whiteboard pop-up bubble that appears in the bottom right corner of the screen.

Navjot Musakola

Teacher

Why are my Smartboard pens not working?

If there is no interactivity, using the tip of one of the SMART Board pens, hold the reset button in for a few seconds until the board beeps. If the pens do not work and the lights on the pen tray do not work accurately, you can swap the socket that the pen tray cable connects to.

Josefina Dijkstra

Reviewer

How do you make a Smartboard touch screen?

To enable Touch Recognition
  1. Press the SMART Meeting Pro icon in the notification area, press Control Panel and then press SMART Hardware Settings.
  2. Select Mouse and Gesture Settings in the list.
  3. Select Enable Touch Recognition.

Erma Swartte

Reviewer

How do you calibrate a Recordex?

After driver is installed you may need to calibrate the touch. This is done easily by running the touch screen application and then clicking on Calibrate and following the steps on screen. If at some point the touch is extremely off then resetting the touch calibration points can be helpful.

Co-Authored By:

EveryThingWhat Staff Editor

6

17th January, 2020

44

94% of readers found this page helpful.

3.9/5

Click a star to add your vote

Similar Asks
Trending