Asked by: Enai Mugaguren
home and garden home appliances

How do you remove ABS P trap?

10
3 Remove the P-Trap.
Loosen the lock nuts holding either end of the P-Trap to the other pipes with a wrench or pliers, then with your hands. Pull the P-Trap off with a downward tug and inspect it for lost items. Do a small jig if you find said items.


Similarly, it is asked, how do you remove a glued P trap?

Mark the PVC pipes attached to each side of the P-trap three inches away from where they join to the trap. Make a straight perpendicular cut through the sewer pipes at both marks, using a hacksaw. Remove the trap. Scrape off all plastic burrs from the cut pipe ends with a utility knife.

Subsequently, question is, how do I unscrew a PVC pipe under the sink? If it's plastic, you can often do this by hand; if it is metal or difficult to turn, use a pipe wrench or adjustable pliers. Loosen the swivel nut at the opposite end of the "P," either by hand or with a wrench or pliers. When the nut is disengaged, lower the curved section of pipe and disengage it from the tailpiece.

how do I fix my P trap?

When the water in the P-trap evaporates, sewer gas can leak straight into your home. Fortunately, there's an easy fix to this problem: just fill the P-trap with water again. To do this, walk around your home with a pitcher of water and pour water down every drain you can find.

How do you remove the P trap from a bathroom sink?

Unscrew the nuts holding a plastic P-trap by hand, gripping the trap firmly with one hand and rotating each nut counterclockwise. You must unscrew two nuts to remove the trap. One holds the trap to the tailpiece, the small length of pipe extending down from the sink, and the other holds the trap to the drain line.

Related Question Answers

Iaroslava Olmo

Professional

How do you remove a P trap without a wrench?

Removing the P-Trap without a Plumbing Wrench
  1. Then, you have to twist the slip nut counterclockwise using a pair of tongue and groove pliers.
  2. Usually at the end of your P-trap that connects to your horizontal drainpipe, you will notice another slip nut.
  3. Finally, you would be able to remove your P-trap.

Aniela Mercatoris

Explainer

How do I loosen a stuck plumbing fitting?

In many cases, though, it is possible to loosen the stuck plumbing fixture.
  1. Tighten the fixture or plumbing nut with a wrench or locking pliers to break the grip of the mineral deposits; then turn in the opposite direction to loosen it.
  2. Apply heat to the stuck fixture or plumbing nut with a hair dryer or heat gun.

Shyla Lado

Explainer

How do you remove a pop up sink drain?

How to Remove a Sink Pop Up Stopper
  1. Lift up and turn lightly on the pop-up stopper to see if you can simply just lift the pop-up stopper right out of the sink.
  2. Find the stopper's tail pipe sticking down underneath the sink cabinet.
  3. Reach your hand in and find the sink stopper nut fastened on the back of the tail pipe.

Angelic Herzbach

Explainer

How do you unscrew a plastic nut that won't budge?

How to Remove Plastic Nuts on a Faucet
  1. Slip a pair of pliers between the fins on the nut.
  2. Grab the handles of the pliers with both hands and turn the nut counter-clockwise.
  3. Consider another option if the pliers don't work.
  4. Tap the screwdriver handle sharply with a hammer.

Doinita Iguer

Pundit

How do you open a clogged sink drain?

Repeat the process until you no longer feel blockage, then reassemble the trap and run plenty of warm water to flush the line. After the drain is open, pour 1/2 cup of baking soda and 1/2 cup of white vinegar into the drain. Cover both openings and let it sit for a few minutes.

Jovana Zoratto

Pundit

Do you glue P trap?

PVC pipes under sinks include the P-trap that connects the drain to the house plumbing. Such pipes can be connected using threaded pieces or with glue. Gluing your PVC pipes creates a much stronger and permanent hold that can only be broken by cutting off the pipes.

Arianna Azzouzi

Teacher

Can P trap be below drain line?

You attach the p-trap directly to the drainage and manuever the p-traps exits into you existing drain. It is not ideal to have the p-trap below the the exit drain because water gravity has to force the water out instead of it flowing downwards naturally.

Weimin Bonavia

Teacher

Do you glue drain pipe?

The first and most obvious way to connect PVC pipe and fittings without using glue is to simply push the parts together. Compatible parts fit snugly together and will not come apart without some kind of outside pressure. The type of fitting you use can also affect whether or not you need to use PVC cement.

Chadli Benzkirch

Teacher

How do you convert s trap to P trap?

You can convert an s-trap to a p-trap by cutting the adapter off, if there is some pipe out of the cabinet floor, if not you have to buy the thin wall compression fittings, but extend the pipe up, offset if necessary put a T offset as high as you can, install an AAV and put in your p-trap.

Xueqin Appenheimer

Reviewer

Why are S traps bad?

It's probably because the water in the trap has completely evaporated, allowing sewer gases to come in to the home. Back to “S” traps – The reason “S” traps aren't allowed is because they have the potential to suck, or 'siphon', water out of the trap as the water flows down the drain.

Dirce Martins

Reviewer

Why does my P trap smell?

A dried p trap will result in a sewer odor emitting from a sink that maybe hasn't been used in a while. A p trap is designed to use water to block the sewer gases from leaking up the drain. If a sink's p trap dies out this can result in a drain that smells bad.

Zoraima Niggl

Reviewer

How far below drain should P trap be?

According to the International Residential Code, the maximum vertical distance between the sink drain and the entrance to the p-trap is 24 inches.

Gwen Buhre

Supporter

How long does it take for P trap to dry?

three to five months

Takeshi Mandelartz

Supporter

What causes a dry P trap?

Dry p-traps occur when the trap or interceptor has lost its water seal, allowing sewer gases to build back up through the drain and into your home. Leaky p-traps can start as something small and turn into something much bigger if the leak isn't fixed right away.

Acisclo Birra

Supporter

Where is the P trap located?

Every plumbing fixture in your home should have a P-trap. Some are located behind the wall or internally on a toilet, but for sinks they are accessible below. Look for a u-shaped pipe extending down from your sink and back up into the wall—that's your P-trap.

Aimar Sava

Beginner

How do you test a toilet p trap?

Twist the Collar Ring, and Look Inside
Grab the collar ring and twist counter-clockwise. Slide it down, empty the water and look inside. If the P-trap is not clogged, the problem may be deeper in the drain line.

Susannah Stitou

Beginner

Can you use plumbers putty to stop a leak?

Can Plumber's Putty Stop a Leak? Plumber's putty may only be used to prevent or stop leaks in specific areas. It shouldn't be used interchangeably with other products such as caulk or tape.

Marzouk Zschocher

Beginner

How do you replace a shower P trap?

Use a circular saw to cut away the subfloor to gain access to the P-trap. Make your cuts along the floor joists so that you'll have something to support the new subfloor. You may need to use a reciprocating saw to split the piece in two before prying it up. Cut the old drain pipe just behind the P-trap.

Maxym Izkiola

Beginner

How do you connect a P trap to a sink tailpiece?

Slide the short side of the P-trap onto the tailpiece that drops down from the sink drain. Move the P-trap up or down to align the trap arm with the opening in the wall. Use a hacksaw to cut the tailpiece if you can't move the P-trap higher up the tailpiece and the trap arm is below the wall drain fitting.

Co-Authored By:

EveryThingWhat Staff Editor

13

19th June, 2020

33

90% of readers found this page helpful.

4.5/5

Click a star to add your vote

Similar Asks
Trending