Asked by: Hadj Betoret
home and garden home appliances

How do you remove mantel from drywall?

9
Work the pry bar between the edge of the mantel and the drywall, starting at the lowest point, and slowly push the mantel away from the wall. If you are removing a ledge-style mantel, work from the bottom. However, if you are removing a surround, working at the base of the fireplace upward is best.


Subsequently, one may also ask, how do you remove a mantel from the wall?

Pound the bottom of the mantel shelf with a rubber mallet to separate it from the wall if it doesn't release when you pry the base of the mantel away from the wall. Tap it gently, but with enough force to pull the nails from the wall. Once it's loosened, pull out on the shelf to remove it.

Beside above, how do I replace my mantel? Here's how to replace your fireplace mantel in a few easy steps.
  1. Step 1 - Remove the Old Fireplace Mantel.
  2. Step 2 - Measure.
  3. Step 3 - Purchase a New Fireplace Mantel.
  4. Step 4 - Attach the Support Ledger.
  5. Step 5 - Prepare the New Mantel.
  6. Step 6 - Attach the Mantel to the Support Ledger Board.
  7. Step 7 - Secure the Mantel.

Herein, how do you remove an old fireplace mantel?

Place a pry bar along the side of the mantel and tap in place with the hammer if it is a full mantel. Begin at the top edge and pry the mantel off the side of the fireplace. Move the pry bar down the side length of the surround; tap the pry bar in place and pry the side piece off until you've removed the entire piece.

How do you fix a loose mantle?

If your mantel expands or contracts from the heat, it can pull loose from the wall on either side. To repair it, pry off the molding strips on both legs and then pry or lift out the facing -- probably 3/4-inch -- and tighten or replace screws or bolts with new ones. Replace the facing and molding.

Related Question Answers

Ales Russo

Professional

How do you attach a floating mantel to Brick?

How to Install a Mantel
  1. Remove the old mantel.
  2. Add support by drilling holes for lag shields, then install lag bolts into the brick.
  3. Measure carefully and drill corresponding holes for the wood mantel.
  4. Push the wooden mantel carefully into place using wood glue for extra support.

Chenghao Mohwinkel

Professional

How do you cover a fireplace with drywall?

When attaching plasterboard to a brick fireplace wall, you have two options: use construction adhesive to glue the drywall directly to the brick, known as the direct bond method, or mount the drywall with screws. Both methods require you to cover the joints with tape and compound.

Sadik Baumjohann

Explainer

How are fireplaces fixed to the wall?

A tiled fire surround is usually fixed to the wall by screws through metal lugs near the top on each side, often there are also lugs towards the bottom; these will be hidden by the wall plaster.

Ghizela Beltrame

Explainer

How do you remove a stone wall?

How to Remove a Stone Wall
  1. Check the stone wall and confirm it does not support other structures.
  2. Break the mortar between stones at the top of the wall.
  3. Remove loose stones from the work area with a wheelbarrow or other implement.
  4. Break the mortar between more stones as you continue to work down the stone wall or fence.

Yuhao Seidel

Explainer

How do you install a fireplace mantel on a rock?

How To Hang A Wood Mantel on a Stone Fireplace using Rebar {before & after}
  1. Drill a hole in the stone fireplace using a mason drill bit.
  2. Cut the rebar to size.
  3. Fill hole with Fuz It (liquid nail)
  4. Insert the rebar into the hole on the stone and hold in place to allow liquid nail to grab rod.

Slavica Klo

Pundit

How do you install a heavy wood mantel?

Slide Over Bolts Method
  1. Locate the studs behind the brick, stone, or faux veneer.
  2. Drive 1/2in lag screws through each of the studs.
  3. Have a helper support the mantel while you mark the location of the support rods on the back of the beam.
  4. Apply construction adhesive into the holes.
  5. Slide into place, admire, and enjoy!

Wellington Patzke

Pundit

How do you cover a marble fireplace?

Paint the Fireplace
Use urethane-based primer and topcoat to seal the paint job. Paint the fireplace surround a single, flat color. Alternatively, use a faux-marbling technique by rolling on two colors. Allow the base coat to dry, then paint in veins to give the fireplace a new "marble" appearance.

Katrine Baraldes

Pundit

How do I get rid of an old fireplace?

Method 1 Removing a Wood-Burning or Electrical Insert
  1. Remove all of the trim from around the fireplace insert.
  2. Remove any nails holding the insert flashing to the wood framing.
  3. Disassemble any pipes, vents, or other pieces of the insert.
  4. Pry the insert out of place with a crowbar.

Alcina Links

Pundit

How is a mantle attached to a brick fireplace?

Squeeze a moderate amount of adhesive into each of the holes in the back of the mantel, then lift the mantel and position it into place, aligning the holes in the back of the mantel with the support rods. Push the mantel onto the rods until the back of the mantle is against the bricks.

Allene Kimo

Pundit

How much does it cost to remove a fireplace?

If you only need to remove the inconvenient or dangerous parts of the system, you can avoid the massive cost of demolishing the entire system and structure. A partial chimney or fireplace demolition might cost a homeowner $500-$2,000, where a complete removal could run $4,000 - $6,000.

Dedicacion Ribiere

Teacher

How do you remove fireplace doors and frames?

How to Remove Glass Fireplace Doors
  1. Locate the two L-shaped brackets at the bottom of your glass fireplace doors.
  2. Unscrew each of the four screws from the brackets using a Phillips screwdriver.
  3. Use pliers to loosen the thumbscrew on the lintel clamps.
  4. Unclamp the door from the top metal lintel bar where it's now loosely attached.

Happy Lukacs

Teacher

How do you remove a gas fire surround?

Gas Fire Surround Removal Tips
Take away the existing fire surround trim. Then you'll need to uncover the metal lugs that are used to secure the surround to the chimney breast. And remove the holding screws. If the screws are rusted into place, you can soak them in penetrating oil.

Kurt Deubel

Teacher

How do I delete a hearth?

Remove Old Hearth
Use demolition hammer with a chisel bit to chip away old hearth and the mortar underneath (as shown). Leave concrete hearth base and firebox floor in tact. Brush and vacuum debris and dust from hearth base. Tip: Wear eye and ear protection and a dist mask when using a demolition hammer.

Terisa Chutchikov

Teacher

How do I remove a tiled fireplace?

How to Remove a Tile Fireplace
  1. Place the tip of a flat-head screwdriver over a portion of the tile's grout.
  2. Move the tip of the screwdriver over 1/4 inch.
  3. Continue working on the grout in this way until you have removed it all.
  4. Slide a putty knife under a tile and move it back and forth to break the bond between the adhesive and the tile.

Armelina Sada

Reviewer

How do you remove a wood fireplace surround?

Remove the Wood Surround
Pry the wood surround off the wall. Insert a pry bar between the wood and the wall along one side near the top of the mantle. Work your way toward the floor, prying the mantle off as you go. Similarly pry off the top piece of the surround.

Sherryl Rahmanov

Reviewer

How far should a mantle stick out?

A mantel should extend a minimum of 3 inches beyond the firebox opening. If the fireplace has facing around the opening, the mantel can also extend 3 or more inches beyond that. Do not guess when sizing the mantel to a room, or the mantel could wind up being too long or too short.

Bente Katzmaier

Reviewer

What should I hang over my fireplace mantel?

15 Mantel Decor Ideas for Above Your Fireplace
  • Mirror. Image Provided by: New Darlings.
  • Art. You don't have to be a fine art connoisseur to feature art you love in your home, and above your mantel is the perfect place to show off your artistic taste.
  • Family Photos. Image Provided by: Pursuit of Handyness.
  • Television.
  • Clock.
  • Wreath.
  • Chalkboard.
  • Window Pane.

Junkal Wieczorek

Supporter

How do you hang a heavy mantle on drywall?

Make sure those marks are level, centered and extend far enough to cover the mantel's length.
  1. drill holes at each mark. Drill Sleeve Holes. Drill holes at each mark using a drill and 3/4" masonry bit.
  2. insert lead sleeves into holes. Insert Sleeves.
  3. drive lag bolts. Drive Lag Bolts.
  4. install the mantle. Install Mantel.

Brenda Antonioli

Supporter

How do you make a rustic mantel?

  1. Cut the wood to size.
  2. Age and distress the wood beam.
  3. Sand down the mantel.
  4. Assess the distressed markings.
  5. Step 6: Stain and apply paint treatment.
  6. Mark the location of the corbels and cut the board for the bottom of the mantel beam.
  7. Create the faux brick corbels.
  8. Attach the corbels to the bottom board.

Co-Authored By:

EveryThingWhat Staff Editor

14

24th April, 2020

41

84% of readers found this page helpful.

4.4/5

Click a star to add your vote

Similar Asks
Trending