Asked by: Ilian Niemoller
home and garden home improvement

How do you spackle a large hole?

35
Place spackle on the edge of your putty knife and hold the knife at a 45 degree angle to the wall. Drag across the hole in a smooth, solid motion, repeating if necessary to ensure the patch is smooth with the wall.


Similarly one may ask, how big of a hole can you spackle?

Spackle can be used to repair holes less than 4 inches (10 cm) in diameter. Anything larger than that, and the spackle won't be strong enough to support itself and will collapse inward. Larger holes will require support like mesh or wire and joint compound to be properly repaired.

Also Know, what household items can I use to patch a large hole in the wall? Mix a tablespoon of flour, a teaspoon of salt and a few droplets of water in a small container. Mix thoroughly until it forms a paste and apply to the hole or crack as you would joint compound. Use a putty knife or index card to remove the excess while it is still wet and allow the rest to dry.

Considering this, how do you spackle a large area?

Holes larger than one inch across are considered large patches, so follow these directions to spackle and finish a large hole so it will virtually disappear.

  1. Step 1 - Wash the Wall to Remove Existing Grit.
  2. Step 2 - Put on Your Face Respirator Mask.
  3. Step 3 - Fill the Large Hole.
  4. Step 4 - Sand the Spackled Patch.

What is difference between spackle and joint compound?

The big difference between spackle and joint compound is the scale in which they might be used. While joint compound can be used for anything from sealing joints, to prepping drywall for its first coat of paint, spackle is going to find its application for much smaller household uses.

Related Question Answers

Huey Espacio

Professional

Do you need to prime over spackle?

Because a spackle patch is more porous than the surrounding surface, it needs to be primed before applying the finish coat, otherwise it will show as a dull spot. There is no need to use a special primer; any water-based general purpose or drywall primer will do.

Soralla Acker

Explainer

Does spackle dry hard?

Lightweight spackling dries hard, but will crumble if bumped, so it is best used for small repairs. Layer the spackling into the area 1/4 inch deep at a time and allow it to dry between layers. Vinyl spackling will typically dry within one to five hours, depending on temperature, humidity and material depth.

Aleena Gerlitzki

Explainer

How do you fill a large hole in the wall?

Tiny nail and screw holes are easiest: Use a putty knife to fill them with spackling or wall joint compound. Allow the area to dry, then sand lightly. Anything larger must be covered with a bridging material for strength before patching compound can be applied. For holes between 1/2 and 11/2 in.

Lucilla Mendibil

Pundit

How do you fix a bad spackle?

2 Answers. Sand down the high spots using rough grit (100 grit) sand paper (they sell it to fit the sander - you'll find the sander in the drywall area and the sandpaper in paints) then smooth it with 200 grit. If you have low points, fill them in after sanding.

Sagrado Arteabaro

Pundit

How do you fill a large hole in a brick wall?

For large holes inside just build up with layers of mortar (horizontally) and broken brick, in a bricklaying fashion. Then flatten the mortar at the front nearly flush for plaster coat. same sort of thing for backboxes, but fill with mortar, and push broken brick into it, finish same as before.

Khuram Marialva

Pundit

How long does spackle last?

Average Shelf Life
Most wet compounds are rated for around nine months to a year so long as the compound is kept in the right conditions. Dry compounds have a similar shelf life of around a year so long as the proper storage methods are used.

Zulay Via

Pundit

How do you smooth out spackle?

Take your time even with small patches so the wall can look its best.
  1. Smear the spackle over the drywall with a flat-edged putty knife.
  2. Spread the edge of the spackle beyond the area you are covering.
  3. Sand the surface of the dried spackle lightly with a fine-grit sandpaper or a sanding block.

Fran Nadeau

Teacher

How do you spread spackle?

Here's a quick how-to to help you apply Spackle to your walls:
  1. Sand down the hole. Rough edges make it difficult to apply Spackle evenly.
  2. Apply Spackle. Load a small amount of Spackle onto your putty knife and smear it over the hole.
  3. Smooth the Spackle.
  4. Apply a second coat.
  5. Wipe down the surface.

Livia Haverbier

Teacher

How do you cover an uneven wall?

Using Paint Effects to Disguise an Uneven Wall
  1. - Repair the biggest cracks and imperfections using filler or plaster.
  2. - Sand the wall using a block and paper or an electric sander.
  3. - When the wall is smooth, wash it down carefully and leave to dry.
  4. - If the plaster is old and very porous, apply a primer.

Lourdes Grossekamper

Teacher

How soon can you paint over spackle?

It may not have been given adequate time to dry properly to help cover your spackle. Make sure to give it around 3-4 hours if possible for best coverage. What type of paint and primer did you use?

Anyelo Sabou

Teacher

Can I spackle over paint?

Yes. However, keep in mind that unless you prime the spackled spot, you will probably be able to see it after putting on your color coat. Even with priming the texture will be a bit different and the spackled area will absorb the paint a bit different.

Coralia Benayad

Reviewer

What is spackle made of?

Spackling paste or spackling compound is made of gypsum powder and binders and is used to patch small holes, cracks and other imperfections like dents in drywall, plaster walls, and sometimes in wood.

Ionut Jewison

Reviewer

Can you paint over wet spackle?

You can fudge a little but you don't want to paint over wet texture. Sprayed texture walls look best if backrolled. That helps to work the paint into all the cracks/crevices in the texture giving a better looking finish. If it was just primer that was sprayed without backrolling it might be ok.

Keesha Torrescusa

Reviewer

How big of a hole can you patch in drywall?

Repairing large holes in drywall—anything over 6 or 8 inches—is different from repairing a small hole in drywall. Small holes can be patched over with drywall tape or a self-adhesive drywall patch, but large holes need a more rigid material to span over the larger opening.

Carlee Hatwagner

Supporter

How do you replace a large piece of drywall?

Remove Damaged Section
Using a level, measure a straight line across the top and bottom of the damaged section. Then use a drywall knife to cut across those lines, stopping at studs that are past the broken areas. Continue cutting down the drywall adjacent to the studs until the entire section is removed.

Saliou Heermann

Supporter

How do you fill holes in wall with toothpaste?

Use Toothpaste to Fill Holes. Toothpaste is a great alternative to spackling if you have a hole in your wall smaller than 1/4 inch. Try to find a toothpaste close to the color of the wall, then squeeze the paste into the hole and wipe off the excess with a putty knife or playing card.

Eleuteria Cremilde

Beginner

How much does it cost to fix a large hole in the wall?

Minor holes cost between $50 and $200 to repair, while larger holes may cost $150 to $400.

Benachir Riemland

Beginner

How do you fix a hole in drywall with spackle?

Steps
  1. Use spackle to repair holes less than 4 inches (10 cm) in diameter. Spackle can be used to repair holes up to the size of your hand.
  2. Buy light spackle at the local hardware store.
  3. Use 150-grit sandpaper on the drywall around the hole.
  4. Scrape the area around the hole with a putty knife so it's smooth.

Barbaro Boura

Beginner

What is the best filler for walls?

Caulk: this is flexible acrylic mastic (such as Painter's Mate), and the best thing to use for filling any gaps that may appear between your skirting board and wall, your doorframe and the wall, or at the edges of shelves that are going to be painted.