Asked by: Ottavio Mullener
automotive road side assistance

What is a intake camshaft actuator solenoid?

Last Updated: 19th February, 2020

34
A camshaft actuator solenoid --normally installed in the front of each cylinder head -- is used to precisely control the flow of oil into the camshaft actuator. This changes the rotation of the camshaft to adjust valve timing and valve overlap on the go.

Click to see full answer.

Simply so, what does the intake camshaft position actuator solenoid do?

Camshaft Position Actuator Solenoid. Car makers use the cam position actuator solenoid valve to adjust the engine timing on the fly. This precise control allows engine designers to squeeze more power and fuel economy out of the engine while maintaining strict emissions standards.

Additionally, what is an actuator solenoid? Solenoid for Pneumatic Actuator Solenoid valves are used to direct air flow into and out of pneumatic actuators. Solenoids are used to remotely control actuator position using an electrical signal. Typically they have two states: de-energized and energized.

Similarly one may ask, how much does it cost to replace a camshaft position actuator solenoid?

In a lot of cases, you will have to pay for multiple parts which can cost $1,000 or more on high-end cars. Since it can take hours to replace the actuator, you can expect to pay hundreds of dollars in labor, usually starting at around $300 and going up to $1,000 or more.

Where is the intake camshaft position actuator solenoid?

Camshaft Position Actuator Solenoid are located on the cylinder head of your Chevrolet or GM vehicle control the position of the camshafts.

Related Question Answers

Sheela Koehnen

Professional

How do you know if your camshaft actuator is bad?

Symptoms of a bad or failing camshaft position sensor
  1. Vehicle does not drive like it used to. If your vehicle idles roughly, stalls frequently, has a drop in engine power, stumbles frequently, has reduced gas mileage, or accelerates slowly, these are all signs your camshaft position sensor could be failing.
  2. Check Engine Light comes on.
  3. Vehicle will not start.

Lies Conde

Professional

What does an intake actuator do?

Intake Manifold Actuator. It transmits power up and down when vacuum pressure is applied, and also adjusts the amount of air intake according to the number of revolutions of the engine for VIS Valve to create the best intake efficiency and for Swirl Control Valve to swirl intake air to generate vortex.

Danial Leiko

Professional

Can I drive my car with a bad camshaft position sensor?

If the engine appears to function normally, as before, it is likely OK to drive it. However, if the engine starts to misfire (you would see a flashing check engine light) then it is NOT OK to drive it all without risk of damage. Diagnostic Trouble Codes can never be used to "directly" condemn parts.

Lluch Lotero

Explainer

What are the symptoms of a bad VVT solenoid?

Here are a few symptoms of a worn out or broken VVT solenoid.
  • Check Engine Light comes on. Since today's modern cars are controlled by an Engine Control Unit (ECU), virtually all individual components are monitored by the ECU.
  • Engine oil is dirty.
  • Rough engine idle.
  • Decrease in fuel economy.

Ridwan Kentia

Explainer

Can you drive with a bad VVT solenoid?

When a car, truck or SUV is driving in normal driving conditions, the VVT is not active. The most common cause of failure for both the VVT switch and the VVT solenoid is a lack of basic maintenance. If your oil is dirty, sludge can clog the screen on the solenoid, causing a failure.

Aiko Reine

Explainer

What happens when a camshaft sensor goes bad?

If your vehicle idles roughly, stalls frequently, has a drop in engine power, stumbles frequently, has reduced gas mileage, or accelerates slowly, these are all signs your camshaft position sensor could be failing.

Beatrice Grippekoven

Pundit

How do you test a camshaft position actuator solenoid?

Testing
  1. Turn the ignition ON, measure for battery voltage between the CMP actuator solenoid high control of the affected actuator and a ground.
  2. Connect a test lamp between the CMP actuator solenoid high control of the affected actuator and a good ground.
  3. Command each CMP actuator solenoid between 0-50 percent.

Zhi Sydli

Pundit

How do I fix the code p0010?

What repairs can fix the P0010 code?
  1. Connect a professional scan tool to verify the code exists.
  2. Perform research from professional sources for testing and values based upon the code.
  3. Check for any other fault codes which may be related to the issue and perhaps clear the fault codes to see which fault codes return.

Arely Toni

Pundit

Can you clean a camshaft position sensor?

Cleaning the Camshaft Position Sensor
Sometimes, cleaning the camshaft sensor can do the trick and bring back your ride's optimum performance. After that, take the sensor out and place it on a clean rag. Step 4: Next, spray some aerosol solvent on the camshaft position sensor and then use a new rag to wipe it dry.

Annabell Rosino

Pundit

Weronika Smith

Pundit

Will a bad camshaft sensor always throw a code?

Answer: Usually a camshaft sensor intermittent failure can produce no code. But you'll notice a change in driveability performance at times.

Edris Yudkin

Teacher

How long does a camshaft sensor last?

The camshaft position sensor on a car is built to last as long as the car does, but in most cases it will have to be replaced well before that. Just like any other sensor or switch on a car, the camshaft position sensor will take a lot of abuse due to the heat that the engine produces.

Jadwiga Schein

Reviewer

Yong Enault

Reviewer

How long does it take to change an actuator?

If you don't run your AC system much after you realize there is a problem, then the damage may not affect any other part of the system, and you should be able to get away with a relatively inexpensive repair. Expect the replacement work to take one to two hours, including testing.

Johann Kekko

Reviewer

How does a solenoid actuator work?

Solenoid valve is a control units which, when electrically energized or de-energized, either shut off or allow fluid flow. The actuator takes the form of an electromagnet. When energized, a magnetic field builds up which pulls a plunger or pivoted armature against the action of a spring.

Vladut Guddat

Reviewer

What is the difference between an actuator and a solenoid?

An actuator is usually a motor and gearbox which can actually control the flow to a more infinite adjustment. If you just need off and on a solenoid valve like on a washing machine works well. If you need fine control of flow an actuator is your best bet. 1) A solenoid valve is an electromechanical device.

Dunja Oldenhofe

Supporter

What does a solenoid look like?

A solenoid is a coil of wire in a corkscrew shape wrapped around a piston, often made of iron. As in all electromagnets, a magnetic field is created when an electric current passes through the wire.

Delila Scheuchenzuber

Supporter

Can I drive with a bad solenoid?

The short answer is that, yes, you can usually drive a car with a bad shift solenoid. Granted, it might not shift past a particular gear, but you should be able to drive it for a short period of time without causing any serious damage.